Complete How To Install The Gypsum Ceiling Material House

Techniques how to install gypsum ceiling for your home ~ Maybe someone asked me in Mool Goole, how do you go about the steps on how to make gypsum ceiling, starting from making the frame to the finish? Ok, we will inform the complete guide here.

There are many ways or techniques in making ceiling gypsum material, and each ceiling builder must have different techniques in terms of installation.

The difference in technique and that can be seen from the way the application of gypsum ceiling frames, suspended ceilings, ceiling closure pairs with jayaboard gypsum board brands, a-plus, knauf, gyproc, up to finshing.

If you like to pay attention to the models of houses - simple, minimalist, luxurious and modern houses that are around you, there must be one house, maybe even a lot now the ceiling in his house, made of jayaboard gypsum board, a-plus, knauf, or Gyproc too.

This is caused by the gypsum board has advantages when used for ceilings, for example in the end result that is produced, especially on the gypsum board connection will look very good and neat.

So that a simple ceiling design will look luxurious, simple but elegant. Besides damage to the gypsum ceiling is very easy way to fix it.

Then How to Calculate Costs and Wages Install a Ceiling of the House you can find here, if you need it to plan a ceiling application in your home.

Making on the ceiling frame of the house, can be distinguished based on the type of frame material used whether you want to use a minimalist wooden ceiling frame, galvanized hollow ceiling frame and galvalum. For understanding the wooden frame maybe all of you already know it.

But for the hollow ceiling frame, or also commonly called the hollow iron, before what was hollow iron? understanding hollow iron is one of the building materials for the manufacture of house ceilings, minimalist ceiling manufacture, gypsum ceiling manufacture, and so forth.

The advantage of hollow as a ceiling frame is that it has anti-termite properties. And the size of the hollow iron that is commonly used in the manufacture of skeletal ceiling is hollow iron 2 x 4 cm and 4 x 4 cm.

In addition, the installation of a frame using hollow iron will feel faster compared to using a wooden frame ceiling. In other words, this ceiling frame work with hollow iron is very easy. If it seems difficult it's because you don't understand it.

Even if you understand it, you still need accuracy and correct techniques in the ceiling installation work, and don't forget that you also need the equipment that you must have if you want to install the gypsum ceiling.

See the Video Guide

Steps - Steps How to Make Gypsum Ceiling

Standard Minimalist Models below:

Before the ceiling frame work begins, first the other types of work that surround the ceiling, or all work related to the roof, must be completed first.

If the work is not finished before the ceiling application starts, it will become a double work later, meaning that even the finished ceiling installation will not be good and will even be damaged, if it has to be tinkered again.

How To Install The Ceiling Of A Gypsum House

But if you insist on trying to install your own ceiling at home, then you may see ways or steps - steps that start from:

1. Work of ceiling frame installation,
2. Closing ceiling frame with gypsum board,
3. Punching gypsum connections by using cornices or componds,
4. Rubbing or Emery of putty
5. Installation of gypsum trim
6. And finally the ceiling painting

Although the way to install ceiling for this house is specifically for gypsum material as stated in the title of the article, but it also applies to the installation of 7 Types of Residential Ceiling Existing in Indonesia.

In addition, the guide or tutorial on how to install the ceiling here applies to the ordinary flat model, and is not included in the 9 Example Drawings of Multi-Leveled Ceiling Frames of Hollo Iron, or minimalist ceiling models that have traps.

Ok, just the following below is a clear explanation contained in the list above regarding the steps - the installation of gypsum material ceiling housing:

1. Install the Ceiling Frame

Before the ceiling frame installation begins, it is better if you know in advance about The Equipment That You Must Have If You Want to Install The Gypsum Ceiling

If you already know what ceiling equipment, then the ceiling frame installation can begin. Installation of gypsum ceiling frame here we will use the Hollow Iron.

How much is the price of hollow iron, can be found in the price of Hollow Iron Per stem For the Ceiling Frame.

And the following are the Steps - Steps to Install the Ceiling Frame that must be passed before closing the gypsum board :

#Step One : Adjust the Ceiling Height

Measure the height of the line around the walls of the room that will be installed ceiling by making several points or marks on the walls of the room.

For example:

• Make 4 points or marks on each corner of the room by using the Water Pass Hose,
• then draw a straight line between one point and the other point using a handyman's pencil strap
• A handyman pencil strap is a pencil that is used to draw or make straight lines, especially straight lines that are too long. Make this straight line on all areas of the wall or around the room.

#Second step: Installation of Wall Angel

There Are 5 Reasons Why Home Ceiling Must Be High For You To Live In. But if you already know and after you make a sign for the height of the ceiling frame, the next is the installation of the ceiling frame type Wall Angel.

The function of the hollo type Wall Angel ceiling is as a supporting frame for hollow metal furing or hollow in the middle of the room.

Place this wall angel in a straight line that had been made right at the bottom of the wall angel, then nails using concrete nails 2 cm or 3 cm in size, position the distance from one nail to another at least 30 cm.

Make sure the elbows are nailed firmly and tightly, do the installation of wall angels on each long line first. Oh yes, In addition to using nails, installation of angel wall can also be used by using a screw in the drill as shown below:

#Step Three: Make a Sign with a distance of 60 cm.

After the angel wall or hollow elbows in all around the walls of the room installed, the next is to measure again on the trunk of the wall angel with a distance of a multiple of 60 cm, starting from the corner of the wall that extends to the next wall corner.

Multiples of 60 cm are meant like 60 cm, 120 cm, 180 cm, then 240 cm, and so on until the end of the wall extends. And don't forget to make a mark at a distance of 60 cm by using a pencil.

Making a sign can use a letter like A, B, C, D, and so on.

After completing the marking on the elongated wall, make the mark again on the other elongated wall or opposite wall, with the same spacing of 60 cm.

The function of this measurement is to place the hollo on the center of the ceiling frame, which can also be called the ceiling bones or the middle hollow stretch for the ceiling frame.

#Step Four: Hollow Stretch for the Middle Frame

After the measurement within 60 cm is completed or the Size of the Strong Ceiling Frame For Residential, then the installation of a hollow can be started by measuring the length of the sign made earlier.

For example, as shown in the picture below the letter A connected to the other letter A, then pull straight with the meter, how long is the meter?

Then cut the hollo to the size you just measured, if the hollow is too long. However, if it is not long enough, then do hollow connection. And if it is difficult in terms of cutting the hollo because it is too thick then it is permissible to use the Price of the Hollo Iron Cutting Machine For the Ceiling Frame, so that the work can be completed more quickly.

After the length of the hollow is suitable, take the hollow over the angel wall, then screw it with a drill.

Perform length measurements and cut back on the other marks, B, C, D, and so on until the mark that was made earlier. If everything is right, attach everything on the angel wall, then screw it tight.

Parable:

• If on one side of a long wall and has a length of 240 cm or 2.4 meters, if divided by a distance of 60 cm, then it will produce 3 signs, namely signs A, B, and C.
• Likewise with the other side of the wall or the side of the wall, which will certainly have the same length, if divided by 60 cm will also produce the same mark. When you make a picture, it looks like the photo below:

#Step Five: The Upper Hollo Expanse for Hangers

The Upper Hollow Expanse is in addition to being a reinforcement as well as a place for screw mounting rods or hangers which will later be connected to the roof frame or not / building castings.

After installation of the hollow in all the signs is completed, proceed to the installation of the hollow above the hollow as explained in point no. 4.

In order not to confuse me in explaining, the hollow explained in point no. 4 is :

• hollow marks A, B, C, and so on, I will name the bottom hollow in short with BB hollow,
• and hollow on point no. 5 I will name the top hollow in short with Hollow BA.

The function of this hollow BA is:

• In addition to locking the hollow BB so that it doesn't shake left and right, it also holds the weight of the gypsum board, and makes it easy to hang when it is screwed.

How to install :

First do the measurements the same as in point no 4, only the difference is the measurement for hollow BA is carried out in the opposite direction with hollow BB.

For example:

• The measurement of hollow BB in the long wall plane, the hollow BA measurement must be on the wide wall plane, so that they cross with each other.

Measure on a wide wall area, then make other marks such as signs 1, 2, 3, and so on with the distance from the sign to the sign that is 80 cm, do also measure and make signs 1, 2, 3, and so on the wall area another one.

After getting the sign, then measure the length from the sign to the sign for example sign 1 with sign 1 and so on, then adjust the length to the hollow BA.

If the length is more then do the cutting, if it is less then do the connection. After fitting, place all of the adjusted BA hollow above the BB hollow.

After all the hollow BA is in position, then screw all the hollow BBs that collide with hollow BA.

Do the screwing on the right side of the kirin, and the middle, until it penetrates the BB hollow, check again not to miss anything that hasn't been screwed. more or less for example as in the 2 images below:

#Step Six: Making Ceiling Frame Hangers

After completing the installation of BA hollow, the next step is to make the hangings from hollow BA and BB hollow to the roof truss or not to the castings.

The ideal distance from each hanger is 80 cm, 100 cm, 120 cm. If you want to be stronger and sturdier then a distance of 80 cm is better. the denser the duct distance, the stronger and stronger a ceiling.

For the use of this hanging, each craftsman is different - some use wire, some use hangers, others use hollow again.

My advice is to use only the hollow that is already available, and in my opinion it is stronger than using hangers from hangers especially from wires.

First measure the height from the hollow BA to the roof truss or not the castings, then adjust the length with the hollow.

If it is fitted first with the upper part of the roof frame, then also the bottom part of the hollow BA and Hollow BB, first make sure the hollow BB evenness.

After all the hangers are attached, make sure all of the hollow BA is still shaking or not. if there is still rocking, you can add more hangers.

Make sure all the hollow is screwed properly so that nothing is loose or dol. For more taste, more or less like in the photo below:

Yup, the installation of the ceiling frame stages is finally complete, next is the closing of the frame using gypsum board or gypsum board. Also Read : Understanding What Is Hollow Iron For Ceiling, With Its Strengths....

2. Install the Gypsum Board :

After assembling a hollow frame for the sake of hollo, it is finished installing, next is the gypsum board installation event or commonly known by the English term is the Gypsum Board.

In this stage it is necessary to know first that the gypsum board or gypsum board has a width and length. For more information, you can visit the article: Size of Gypsum Board for Residential House Ceiling. or can directly to the size of the gypsum board below:

Gypsum Board Width and Length :

• Gypsum Board Width: 120 cm,
• Gypsum Board Length: 240 cm.

If you do not know the price of the latest gypsum board, then may stop briefly in the article: Price of gypsum per sheet based on famous types and brands.

As explained earlier in point 3 and point 4 in the frame installation step, the distance between the hollow BB is 60 cm. If 60 cm + 60 cm = 120 cm, then the size of the gypsum board width is 120 cm.

Likewise with the length, if you continue to add 60 cm, you will find the number with the length of the gypsum board that is 240 cm.

The gypsum board mounting position when it will be attached to the hollow frame also actually depends on your own taste.

This means whether the gypsum board wants to be installed facing lengthwise to the east, or whether it wants to be installed facing west. what is certain is the length of the gypsum board must be adjusted to the hollow frame and must also fit, especially in the connection on the gypsum board. So that the gypsum board can be screwed properly.

Even so, it really needs to also think about the direction of the gypsum board before closing. By way of estimating first, approximately closure in which direction is better, so that later there will not be too much cutting on the gypsum board later.

Because the installation of gypsum board is the same as the Guide to how to Install Floor Tiles for Residential, where at each edge or side of the room there must be a difference or remaining size.

Likewise with the installation of the ceiling of this gypsum material if there is a difference or the remaining size, it must be done How to Cut the Gypsum Board Good and Right

Next, do the gypsum board installation using screws, and this is the right length of screw fitting to install the ceiling, with screw lengths of 2.5 cm.

Do the screwing on the gypsum board on the track with the hollow BB. The ideal size between screws is 10 cm,

Make sure the screw is a little into the gypsum board, so that it will be easier when you will later start the compon or pickup by using a-plus cornice on the gypsum board connections.

(Gambar)

If all gypsum boards or gypsum boards are installed, make sure all screws are correct and strong. If so, the next step is capture.

3. Overhaul Gypsum Board.

Yup, then we enter the landing stage on the gypsum board. What happens if the connections on the gypsum board are installed and also in the screw holes if not putty? Oppps of course the ceiling will look really bad isn't it ... hehehe.

Disadvantages and Strengths of the Gypsum Ceiling and one of its advantages is the invisible connection and also the screw holes on the Gypsum board, and that is true, but it depends on the way of caulking as well.

If the picking up is done carelessly or carelessly, then the connection on the gypsum board will still be visible.

So this landing stage is the stage that determines the final result whether the ceiling looks tidy or not.

To get a good end result on the ceiling so that the gypsum board connections are even and invisible, it requires skills with a high level of patience and also real eye foresight when working on it.

A good jump is a repeat that is repeated. This means that it is not enough just 1 time, but must be up to 2 or 3 times, if the taste is still not flat, do it again until 4, or 5 times.

The material for this forging is Cornice mixed with water. Good mixing should be a little thick and not too runny. but also not too much, because the cornices dry a bit.

If you don't know what the putty material is, then you can check the name in this article: The name of the putty material and how to mix it.

Then if you mix cornices in a quick-drying taste, then there is a solution and the solution is to listen to this article: "The Secret", So that the Coumpond Complain Does Not Dry Quickly.

If we feel that we understand it, then we return to the subject of the discussion, which is the initiation of capture. But before you start petting, please prepare the putty tools that are needed as follows:

• Scrap Putty,
• Small Bucket,
• Dam Putty Knife.

Keep in mind on the left and right edges of the gypsum board that extends, if you look carefully the thickness is a bit thin.

The way to find out, prepare a ruler or caulking tool can also, then put between the gypsum board connection, then at the bottom of the ruler there will appear a little gap or cavity, and that means the gypsum board is not flat.

To flatten it, in an area where there are gaps it must be put up periodically until the gap is not visible.

So the gypsum board must be done in the following sections:

• Gypsum Board Joint
• Screwing holes
• Gypsum boards that are injured or have defects.

Especially on the edge of the gypsum board on the edge of the wall, if you want to attach it to the gypsum list profile or frame, then there is no need to do it in the process.

Because later also the gaps or holes of the screw that looks will be closed by itself by gypsum list profile. However, if the gypsum list profile is not installed, then it must be done by the way to do it.

If all of the tasting is done and the taste is flat, then the next step is to go into the rape or sandpaper stage of the parts that were putty.

4. Gypsum Connection Rubbing

Use sand paper like the photo above to rub or smooth the parts on the putty gypsum board. Sand paper is usually sold in units of permeter. How much can you check the price of sand in the article Price of Sand Paper For Rubbing Putty On The Ceiling.

There are 2 polishing techniques that we usually use:

• Dry Rubbing Technique
• Wet Rubbing Technique

What is the dry rubbing technique?

• The technique of dry rubbing is the technique of rubbing directly with sand paper on gypsum board parts that have been putty, without using water.
• If you want to use a rubbing technique like this you have to prepare a head covering. Because the dust - generated dust can pierce the eye until it hurts.

What about the wet scrubbing technique?

• Wet scrubbing technique is scrubbing technique by wetting the gypsum board parts that have been putty using a hand brush or a brush,
• then rub with sand paper,
• then wipe the scrub again with a putty tool, scrap, until the foam or lump of water disappears.
• Previously you prepared a small bucket of clean water.
• If the water is dirty, then replace the dirty water with clean water.
• do repetitive strike until evenly distributed on all parts of the gypsum board that has been putty.

It's up to you which one you want to use, admin advises if in a private home, especially if there are already residents, it's better to use a wet polishing technique.

Because to avoid discomfort in the house, but also to maintain health in the eyes and breathing especially for residents of the house.

If all scrubbing is complete, the next step is to install the gypsum trim profile on the ceiling edge.

5. Installation of Lis Gypsum Profile

As has been discussed in previous articles that the gypsum trim profile is a decorative ceiling mounted between the corner of the wall and the edge of the ceiling. In addition, it can also be installed between the upper ceiling with the lower ceiling.

The upper ceiling and the lower ceiling in the world of plafoners are commonly referred to as traps or levels. In other words the profile of the gypsum trim is the ceiling frame.

Like a photo on the wall when not using a frame, it certainly would be less beautiful in view.

So also with the ceiling of the house, so that it looks more beautiful and charming, then one way is to have to put on the gypsum trim profile around the edge of the ceiling of the house itself.

Many available various sizes of gypsum trim profiles, ranging from a small size of 5 cm to a large size of 20 cm, and the length of the gypsum list profile in general are the same at more than 2 meters.

Gypsum trim motifs also vary. There are floral motifs, plain motifs, line motifs, and others.

In other words, accessories for the ceiling using a gypsum board are available in many models and types.

One of the accessories that are often used apart from the gypsum list profile is the Dop Lamp or Center Panel which is commonly used to place lights that you can learn on How to Install the Dop Lights on the Gypsum Ceiling.

Speaking of light bulbs, there is also such a thing as Downlights. Types and Prices of Downlights as a Ceiling Decorator, meaning that these downlights can be installed at ceiling corners to make the ceiling look more beautiful and attractive.

Info on the size and name of the gypsum list profile motif can be found in the article: Latest Gypsum List Prices for Ceiling Frames.

Next

Ok, before starting the installation of the gypsum list profile, first prepare the equipment as below:

• The same cornice for gypsum board sumping
• Buckets for clean water.
• Putty knife (see photo in the forging stage)
• Putty Scrap (see photo in the forging stage)
• Sand paper.
• Gypsum List.

Especially for Gypsum List Profiles if you don't know how to calculate their needs, you can stop by briefly in the article: How to Calculate Gypsum List Needs.

If so, then you can proceed to the Steps - Steps How to Put the following Gypsum Profile List:

The first step :

Make a straight line around the wall on which the gypsum list profile will be mounted by measuring downward from the surface of the gypsum board on the edge of the ceiling, then making a mark.

Make this mark on the 4 corners of the wall, to later draw a straight line using a pencil strap. for more details about the results of the lines like the photo below.

How to determine the size of the surface of the gypsum board for example:

• In the photo above it's 7 cm, when using the gypsum list profile which has a width of 10 cm.
• But if you want to use a profile list that has a width of 14 cm, then the distance decreases from the surface of the gypsum board is 9 cm.

The function of measuring and making this line is to set the slope and straightness of the gypsum profile list to be installed.

It is important to remember that mounting upright on the gypsum list profile is not good, and vice versa if the installation of the gypsum list profile is too tilted, it is also not good.

So the size that I inform is the ideal size ...

Second step:

After the straight line around the wall is complete, then destroy the acian on the wall using the Hammer .... !!!

"How come it's broken bro? Calm down friend,

The purpose of the destruction of acian here is not the entire wall that has been aci it damaged. But only on the wall that had been made just a straight line.

So give me a little bit of wound, until the plaster looks right on the line, not above the line.

The purpose of destroying this dictation is that later the result of gypsum list gluing profile on the wall is closer or more attached. So that the List Gypsum Profile will not easily crack and quickly fall.

You see, there are many cases of cracks or gypsum list profile dropping, because the wall is not wounded first. So do all the opening of the wall around the already made straight line earlier.

Third step :

After finishing the wall the next step is to attach the gypsum list buffer or retaining profile using screws or nails to the fitting wall in the straight line that has been explained in the second step above.

This barrier is temporary, yes, where if the glue is dry, then this barrier must be removed.

Make a holder for one gypsum list profile bar at least 3 holders, for example at one end, one in the middle, and at the other one.

Perform a profile list installation

Perform the installation of the 2 bar gypsum list profile first. For the list motive is up, it could be a plain motif or flower motif.

Installation The two gypsum list profile bars are started from 2 different wall angles, the rest will just stay connected.

Fourth step:

It's time to install the gypsum list profile on the wall that was made straight line earlier. The first thing to do is:

• Expand the gypsum list profile on the floor, if you use shifting stelling. But if you use full stelling, then the extension can be done on stelling.
• Determine the position of the motif on the gypsum profile list. For example in plain motifs there are usually small straight lines and there are also curves.
• So if these straight lines want to be at the top, then the cut must be noticed later.
• After getting the position, cut the beveled edge of the gypsum list profile as shown below:
• Cutting these edges to place in the corner of the wall. then cut straight at the other end about 5 cm.
• If you have prepared cornice glue, putty knife, a small bucket for mixing putty, and clean water.
• Mix cornice glue and clean water, make it slightly thick, then stir until mixed,
• then apply cornis glue using a putty knife on the sides of the upper, lower, left, right gypsum profile list.
• After that, stick to the line 
• To avoid falling because the glue is still wet, help with a screw at the top of the gypsum list profile.

If the steps - the installation of the gypsum list profile above is still a bit confused to understand, Try reading this article: 6 Practical Steps How to Put a Gypsum List Profile.

6. Ceiling painting.

For how to paint the ceiling I think everyone already knows and anyone can do it. So there is no need to explain anymore. Or to make it clearer and more certain, please read the article: 6 Steps How to Paint a House Wall

The point is before painting, first choose the colors that are suitable to be applied to the ceiling that has been installed. If it feels appropriate and appropriate then just apply it.

Ok maybe that's all that can be informed about How to Install Gypsum Ceiling Materials for your home. Good luck and thank you for stopping by. May be useful.

Share :